Tenbrook Archery
831-212-5779
  • Home
  • Longbows
    • Phenolic/Carbon Fiber
    • Mango/Koa
    • Ebony/Etimoe
    • Walnut/Etimoe
    • Purpleheart/Maple
  • Wood Gallery
  • Photos/Videos
  • Tutorials
  • Contact

Beaver Tail Grip

10/18/2013

4 Comments

 
Here's what you do:

1) Cover the handle in plastic wrap to protect from moisture.

2) Soak the Beaver Tail in warm water for 10 minutes.

3) Remove from water and pat dry then wrap tightly around the handle stretching it to conform around the curves of the grip. Get all the wrinkles out then wrap tightly with plastic wrap.

4) Come back in two hours and remove everything.

5) Let the tail dry 24 hours then trim to size.

6) Glue on with "Barge Cement" and lace up.

SUPER EASY!
Picture
4 Comments

Shave Horse Plans - Bowyers Bench

11/12/2011

18 Comments

 
Here are some plans for building a Shave Horse - Bowyers Bench.

Enjoy!
Picture
Picture
Picture
Picture
Picture
18 Comments

Bamboo Arrow Build-A-Long

10/15/2011

18 Comments

 
Picture
Bamboo Arrow Build-A-Long

First go to Home Depot and buy some 72" Bamboo Plant Stakes. They come in a 6 pack. Buy as many as you like expecting to get 3-4 usable shafts per bag.

You will also want to pickup some 16D Duplex Nails.


Picture
Now go through the bags and pick out the straightest pieces with a OD (outside diameter) of between 7-10mm. It helps to have an open end wrench handy to help gauge the OD. We are going to be making these into 32" shafts so the OD only needs to be between 7-10mm for a 32" section.


Picture
You should now have a pile of hand picked 72" Bamboo Plant Stakes with an OD of between 7-10MM over a 32" section.

Picture
Now we need to cut the Bamboo Plant Stakes down so they are more manageable for the straightening process. Bamboo likes to split when being cut so be careful here and use a sharp/fine tooth saw.


Picture
When cutting the Bamboo you need to find the best section of your 72" stake. Bamboo has a natural taper. The thick end of you bamboo is going to have the point. The thin end will have the nock. Take this into account when cutting the Bamboo. You will want your cut at the nock end to be about 1.5" past a node. We will be using the node to help setup the Self-Nock later on. Go ahead and cut the shafts down to only about 36-40" at this point. You want to leave them a little long to help with straightening.

In this picture you can see where you want to have the cut for the nock end in relation to the Bamboo node.

Picture
For straightening the shafts I like to use a heat gun. Just about any heat source will work.

Some people like to straighten the nodes first. Some like to do the mid section first. It does not seem to matter either way so choose which one you like. I start with the nodes.

I take my heat gun and place it under the node while spinning the shaft. Once the section I am heating gets hot enough the Bamboo will bend very easy. Just bend it as straight as possible and move on to the next node.


Picture
After you do the nodes move on the section between the nodes.


Picture
Next we need to cut our straightened shafts to length (32") and sand down the nodes. Some people leave the nodes as is. I prefer to sand them down. The choice is yours.

Picture
Before and after of the sanded nodes.


Picture
When cutting the nock end only take off a little bit. You want to leave a node about 3/4" above the nock end (skinny end) for setting up the Self-Nock. After cutting the nock end measure 32" and trim the excess off the front. Do not worry about node placement on the point end (fat end) it does not matter.


Picture
You should now have nice pile of straightened, sanded, cut to length (32") shafts with an OD of between 7-10mm.


Picture
Now we will attempt to spine our arrows. Once again some people do not bother to spine their Bamboo Arrows. I will be. For optimal arrow flight you will want your arrow spine to match the weight of your bow.

I do not have a spine meter so this is how we will be doing it.


Picture
Take two of your 16D Duplex nails and nail them level to a flat surface 26" apart.


Picture
Next go into your quiver and grab an arrow that shoots well out of your bow. Place the arrow on the two nails and hang any 2lb. weight from the middle.

Picture
Make a mark in the middle where the arrow flexes to it furthest point.


Picture
Now go through your Bamboo Shafts and do the same thing. Place the shafts that are +/- 1mm from your mark in a separate pile.

Picture
Make a mark in the middle where the arrow flexes to it furthest point.


Picture
 While doing this spin the shaft with the weight on it and find the stiffest side. This is the side you want facing the bow. Make a small mark on the nock end so you know where to place your Self-Nock.  Make a small mark on the nock end so you know where to place your Self-Nock.


Picture
You should now have pile of spined, straightened, sanded, cut to length (32") shafts with an OD of between 7-10mm and a mark for your nock.

Picture
Now we will be sealing our shafts to protect them from moisture. Just about anything will work here. Before appling my finish I like to straighten the shafts on last time.


Picture
After straightening apply your finish however you like. Some spray, some wipe. I just use an old rag to wipe on a nice thick coat then set aside to dry.

Picture
You should now have pile of sealed, spined, straightened, sanded, cut to length (32") shafts with an OD of between 7-10mm and a mark for your nock.


Picture
On to the Self-Nocks. This is where the project becomes more fun IMO.


Picture
First I drill a 7/64" hole 3/8" from the back of the arrow at the nock end (Skinny end) on the same side I marked the stiff spot on the arrow.


Picture
Then using a razor blade I cut into the hole I just drilled.


Picture
Do the other side and pop out the center.


Picture
Get a piece of 80gr sandpaper and fold it in half twice so it is 4 layers thick. Use this to clean up the nock.


Picture
All cleaned up.

Picture
Now take a piece of 220gr sandpaper and place in over the sharp edge of a piece material. Use the edge of the sandpaper to create an angle at the end of the nock.


Picture
Angle at the end of the nock.

Picture
We have to wrap the Self-Nocks to prevent them from splitting. I'm using Artificial Sinew. Any thread will work.


Picture
I start by gluing my Sinew down with a little dab of Super Glue.


Picture
Then I just wrap down the arrow about 1/2" and secure the Sinew again with a little Super Glue. Try and get this nice and tight.


Picture
Cut off the extra and coat the whole thing in clear nail polish or Super Glue.

Picture
 You will also want to saturate the inside of the nock with Super Glue to add strength.


Picture
Nocks are all finished up!

Picture
Time to turn the 16D Duplex nails into points. Take a nail and chuck it up in your drill.


Picture
Now head over to your sander and spin the head with the hand drill while you slowly taper the tip to a fine point (both the drill and the sander are moving in this picture even though it does not look like it).


Picture
Finished head should look like this and is now ready to be installed in our shafts.


Picture
Finished head should look like this and is now ready to be installed in our shafts.


Picture
Now we will install our 16D Duplex Nail Points into our shafts. If you want to cut your shafts shorter then 32" now is the time to do so. I am leaving these full length.


Picture
First drill out the center of the shaft with a 5/32" drill bit (or a little smaller size OD drill bit then the nail). The shaft will want to split so go slow.

Picture
Next heat up the nail red hot and push the nail in the shaft. Make sure the nail is red hot or it will not want to fit all the way. Go slow and don't push to hard.


Picture
Once the nail fits all the way in let it cool for 10-15 minutes.


Picture
When its cool to the touch pull out the nail and squeeze in some Gorilla Glue. I like Gorilla Glue because it fills the gaps. Any glue will do.

Picture
Then I wet my nail (Gorilla Glue likes one side wet) and insert it in the shaft.

Picture
Come back in a few hours and the Gorilla Glue should be dry. It will fill any gap it between the head and the shaft with foamy glue.


Picture
Give the tip a good sanding to clean up the extra glue and to slightly taper the area around the marriage between shaft and point.

Picture
Now sand the whole shaft (except the Sinew wrapping) with extra fine steel wool.


Picture
After a good sanding with the steel wool apply the final few coats of finish. Unlike the first coat (heavy) this time do 2-3 (light) coats.

Picture
Now that our finish is dry we will attach the fletching.


Picture
Glue your feathers on to the shaft using your jig. I use Duco Cement.


Picture
Start with the Cock Feather.

Picture
Second Feather.

Picture
Last one.

Picture
Then add a little dab of Duco Cement to the front and back of each feather.


Picture
Front.

Picture
Back.

Picture
Now we need to wrap the front of the feathers with Artificial Sinew to help keep them held down.

Picture
Just like the nock I start by gluing my Sinew down with a little dab of Super Glue.


Picture
Then I just wrap down the arrow about 1/2" and secure the Sinew again with a little Super Glue. Try and get this nice and tight.

Picture
Cut off the extra and coat the whole thing in clear nail polish or Super Glue.

Picture
Finished!

Picture
Feel free to ask any questions.

Thanks and enjoy!

Tenbrook


Picture
Picture
Picture
Picture
Picture
Picture
18 Comments

    Tenbrook Archery

    Thank you for visiting my website.  Here you can find some examples of the custom longbows I build as well as some archery tutorials.

    Due to an ever increasing demand and a very large backorder I'm currently unable to accept new orders. I apologize for any inconvenience. Follow my Facebook page for any updates.

    Thanks again for your interest!

Powered by Create your own unique website with customizable templates.